7 Simple Steps in Producing a CD Wallet

· Uncategorized

In creating a CD wallet, the first thing you must do is prepare the materials. Follow it with the removal of the stickers from the floppy disk surface, and cutting one part off it. You can then punch openings on the diskettes and attach the binder rings. After that, put the CDs inside the wallet and secure them in place.

CD wallets are amazing things since not only do they allow you to maximize a little space, but they also make it super easy to carry along the CDs wherever you want. And while CD wallets are very common and cheap, they oftentimes only have one look. You can hence create a custom CD wallet that’s unique from others.

Prepare the items

Creating a CD wallet from old floppy disks isn’t just a very unique idea but it is also very easy to do. Moreover, it’ll also allow you to recycle your old and no-longer-utilized diskettes which are just sitting inside your floppy disk holders. However, making CD wallets from old diskettes require you to have all the items you need on hand. By doing this, you can instantly complete your task and get right to utilizing them at once, as well. A few of the items can even already be found in your house, while others may need to be purchased from the retailer. Whether or not you have all the items on hand or not, the following are what you’ll need: 5 ¼ inch floppy disks, a degreaser like goo gone, a razor-sharp set of scissors, a couple of paper towels, two binder rings, a paper puncher, and a strip of ribbon, leather, shoelace or perhaps small chain. You could have as many diskettes as you want that you have readily available for your wallet. Just make sure that you also get the perfect dimension of ring binders for all of them. You can also obtain these things in most office supplies stores.

Remove the stickers from the floppy disk surface

With your degreaser or goo gone, take out the stickers from the surface of the floppy disks. The sticky remains of the stickers should slide off quickly with the degreaser. And all you must do to also eliminate this item and get the surface fully clean is to wipe it off using the paper towels.

Cut one side of the floppy disk

Get your pair of scissors and one of the floppy disks. Find out the notches on the bottom edge of the floppy disk and cut off this edge just over the notches. Once you have cut off the base edge, take the disk out of the floppy disk and throw this away. You should now have an empty floppy disk case with you. And then, do the same procedure with the rest of the diskettes that you wish to utilize.

Punch holes on the disk

Using your paper puncher, make 2 openings on the floppy disk case. Put all the holes so that they are half an inch from the side adjacent to them and half an inch from the top or uncut edge. Punch another hole at the end side and at the center, too.

Attach the binder rings

Open the two binder rings and slide one ring into each one of the two holes at the uncut side of the floppy disk case. Place all the floppy disk cases through the rings then close the rings.

Place the CDs in the wallet

Get the CDs and place them one at a time inside each floppy disk case.

Secure the CDs in the case

Utilize your strip of ribbon, shoelace, chain or leather to close the CD wallet by putting it into the opening at the open end of the wallet. In this way, the CDs won’t fall off from the case.

You may then add your personal accessories to the surface of the CD wallet. You can use stickers that have characters on it or your name.

Find floppy disk holders at http://www.everydayplastics.com/FloppyDiskHolders.php

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: